僅供個人參考

  高性能密閉蝶閥，普遍适用于建材、玻璃、礦山、電力、輕工、造紙等行業的通風、環保工程等管道系統中。對管道中氣體介質按不同控制信号調節流量大小和切斷。

  This valve is widely used in the pipe system such as venting and environment protection in building material, glass, mining, power, light industry and papermaking departments. It can change the flow and cut off gas medium in the pipe by the different control signal.

結構特點：

Structure characteristic:

  高性能密閉蝶閥具有重量輕、結構緊湊、耐磨損、流阻損失小♉、工作壓力高、密封壓差大、操作靈活、指示方位明确✂️、維護方便、使用壽命長等優點。可任意角度安裝❗，特别适㊙️用于調節切斷和要求快速自保的⁉️場合。配用DKJ、ZKJ、伯納德等電動執行🍓器及有關配件，可實現手動、自動無幹擾切換，微機程控、自🐆動控制或中央集中控制，是實現自動化控制操作、調節流量的理想設備。

  The valve has the features of lightweight, compact structure, endurance, little in the lost of flow resistance, high working pressure, flexible operation, definite direction, easy to maintenance and long life. It can be installed at any angle. It is suitable in the condition of adjusting, cutting off and self-protecting quickly. The valve is used with DKJ, ZKJ, Bernard electric actuator and other accessory to form a complete set to realize manual and automatic exchange without interference, micro-computer long-range control, automatic control or center concentrating control. It is the ideal equipment of realizing operation of automatic control and adjusting flow.

性能參數：

Performance parameter:

DM H X Z S---6、10、16、25外形連接尺寸：

Appearance joint dimensions:

工作原理：

Working principle

采用雙偏心密封結構，關閉時越關越緊，開啟後确🐪保密封面👅與密封圈完全脫離接觸，保護密封圈不受損🔞傷，延長使用壽💔命。密封面、密封圈選用不鏽鋼制作，其耐鏽蝕、耐高溫👄性保證了密封🐪性能的可靠。采用半軸結構，蝶闆為桁架式結構，其強度高、過流✉️面積大、流阻小、節省能源。本閥具有介質雙向截止密封功能，其滲漏量為零。

手動高性能密閉蝶閥；通過轉動手輪，經蝸輪副減速，帶👄動👨‍❤️‍👨閥💃🏻軸、蝶闆作90°範圍内的旋轉，達到截斷、連通或調節流量的目的。閥門的開啟或關閉位置均由限位機構限位，并有指示機構🛀🏻顯示蝶闆位置狀态。

自動高性能密閉蝶閥；由電動執行器接受變送、調節DCS、PLC等上位😍儀🍉表的控制信号或操作器手控信号，輸出角位移帶動傳動㊙️軸，把動力傳給閥軸帶動蝶闆作同步旋轉運👨‍❤️‍👨動，達到全開、全🏃閉及任意調節的目的。電動執行器與蝶闆的開度同步反饋0～10mA或 4～20mA直流電信号，用戶可根據電流信号來控制蝶闆的任意開⁉️度，達到調節的目的。

The valve adopts double eccentric sealed structure. The more it is close, the more it is tight. The sealing surface will separate from sealing ring, which prevent the sealing ring from damaging. The material of sealing surface and ring is stainless steel whose resistance of abrasion and high temperature ensure the reliability of sealing performance. It adopts half shaft structure and the butterfly disc is trussed structure, having the features of great strength, big flow area, little lost of flow resistance and saving energy. The valve has the function of stopping and sealing medium in double directions and without leakage.

Manual high performance sealed butterfly valve: rotate hand wheel to drive the valve axle and butterfly disc rotate in the range of 90°to cut off, connect or adjust the flow. The open or close position of the valve gate is limited by the limit device. The indicating device displays the position of butterfly disc.

Automatic high performance sealed butterfly valve: control signal or manual signal of DCS or PLC meter is accepted, adjusted and transmitted by electric actuator. Then the actuator outputs the angle moving to drive the transmission shaft. It drives the axle and disc rotating synchronously in order to adjust freely, full open and close. The open angle between actuator and disc’s sync feedback DC signal is 0～10mA or 4～20mA. User can control the random open angle of disc according as the current signal.

安裝及調試：

Installation and regulation

l  安裝前必須清潔閥體内腔，不允許有任何雜物和污垢附着👅（特别注意密封面、密封圈的清潔）。

l  安裝前檢查閥門各部位是否有松動現象，對閥門⚽進行🈲開啟、關閉一個周期是否有異常現象，同時檢查閥🈲門的啟閉💃🏻位置是否🥵準确。

l  水平安裝或垂直安裝的閥門閥軸應處于水平位😘置，傳動‼️裝置不允許作起吊用，并嚴禁損傷。

l  本閥具有一定的雙向密封性能，若隻需控制單方向流動的🏃🏻‍♂️介質時，其安裝方向應參照閥體上箭頭🐕所示✉️，該箭頭所指為介質流向。

l  安裝如示意圖，加密封墊後均勻鎖緊聯接螺栓。

l  調整完成後必須進行綜合性能檢查：接通電源開啟閥門，當閥♊門至“全開”“全閉”位置時，行程控制機構應準确地切斷電源，而轉🌐矩限位機構處于臨界動作狀态。開度指💯示機構☀️應準确🧡地顯示閥門的開啟狀态。

l  電動切換手動操作時，應切斷電源，不得在手輪上再增加輔助✂️杠杆，手輪順時針旋轉為關，反之為開🚶‍♀️，閥闆👈開啟🚩角度🌂為0°~90°。

l   The body must be cleaned before installed and there is no dirt and sundries clinging to the body, especially the sealing surface and ring.

l   Check the valve gate before install. Open and close the valve by hand for a period and check the open-close position of the valve gate.

l   The valve axle must be on the horizontal position when installed in horizontal or vertical. The transmission device cannot be hoisted and avoid damage when installed.

l   The valve has the feature of double-sealing performance. The installation direction should refer to the arrow on the valve body, which indicates the medium flow direction, when control the flow of medium in single direction. 

l   Installation of flange connecting valve is on diagram. Lock down the connecting bolt after add sealing washer.

l   Synthetic performance of the valve must be done after adjust is over: turn on the power and open the valve, the stroke control device should cut down the power exactly when the valve is in the state of full open or full close. While the torque limit device is in critical state. The open angle indicating device should display the open state of the valve gate exactly.

l   The power must be shut down when operating by manual. Assistant pole can’t be added to hand wheel. Clockwise rotation of hand wheel means open and anticlockwise means close. Open angle is 0~90°.

運輸及保管：

Transportation and protection

l  運輸時應避免撞擊蝶閥及傳動裝置，閥門應處于😘全🔞閉位置，以防在運輸中密封面和傳動部件損壞。

l  當閥門水平放置運輸時，傳動裝置及傳動部位應懸🏃🏻空✏️，以防🔴止傳動軸受力過大而變形損壞。

l  該閥應存放在幹燥的室内，不允許露天存放或堆置🛀🏻。長期存放時應使閥門處于關閉狀态，各傳動部位加潤滑油，傳動裝⛱️置作防潮、防塵處理。

l   Avoid bumping of valve and transmission device. The valve is in full close in order to avoid damage of sealing surface and driving part.

l   Transmission device and part should be hung up when the valve is in horizontal in order to prevent damage of driving axle.

l   The valve should be stored in dry room. It should be in full close state when long stored. Add lubrication to the transmission part and the device should be dampproof and dustproof.

維護及檢修：

Maintenance and examination

l  定期檢查傳動裝置的運行情況：電機部分、控制開關是✉️否異📱常。

l  定期給閥的傳動部位加潤滑油。

l  定期檢查閥的密封填料處，補充、更換填料以防介㊙️質外洩。

l  對閥門周期性維護時應全面檢查閥的各密封部位、傳動部位，對各密封部位應進行檢測，對檢測數據應👨‍❤️‍👨記錄在案。

l   Check the working condition of electric parts, control switch and sealing of pneumatic device regularly.

l   Add lubricant to the transmission parts regularly.

l   Check the sealing filler of the valve regularly. Complement or change filler avoiding leakage of medium.

l   Check the sealing parts and transmission parts thoroughly. Detect the sealing parts and the detecting data should be registered.

訂貨須知：

Information for order

l  選用訂貨時，請參照産品樣本注明産品規格、型号、客戶選用執🛀行器代号及技術參數（使用溫度、設備工況、介質性質等）。

l  選用訂貨時，若未注明客戶選用傳動裝置代号的按我公☎️司基本型配置，其基本型為普通型裝置，不帶任何有關特殊要求及相關配件。基本的傳動裝置、電氣🈲裝置為普通型，如有其他特殊要求（戶外、微控、防爆等）請在合同中注明。

l  表中未列的規格、用于特殊介質或其它特殊要求，請與我公司經銷部、技術部聯系，可為您另行設計、制造。

l   Please indicate the type, model and technical parameter (using temperature, working condition of equipment and characteristic of medium etc) referring to the product sample when you place an order.

l   If you don’t indicate actuator code selected by user when you place an order, we will select the basic collocation of our company for you. The basic type is a normal type without any special request and corresponding accessory. The basic transmission device and electricity device is normal type. If you have especial demand (anti-explosion, outdoors and micro control etc), please indicate in the contract.

l  If you have other special demand, need special medium or the data that is not listed in the table, please contact with our department of market and technology. We can design and manufacture for you especially.